For all Firebird - Trans Am Enthusiasts
Welcome,
Guest
. Please
login
or
register
.
1 Hour
1 Day
1 Week
1 Month
Forever
Login with username, password and session length
News:
Home
Help
Login
Register
»
TAC Tech
»
Electrical
»
Fuel sending unit wiring
« previous
next »
Print
Pages: [
1
]
Author
Topic: Fuel sending unit wiring (Read 2170 times)
Avalanche
Forum Member
Posts: 5
Fuel sending unit wiring
«
on:
April 10, 2021, 12:28:37 PM »
Anyone got a schematic for the wiring from the fuel tank/sender forward? My gauge is not working.
Logged
b_hill_86
Oracle Forum Member
Posts: 2135
Re: Fuel sending unit wiring
«
Reply #1 on:
April 10, 2021, 03:47:18 PM »
Not much to it. One wire from the sender to the gauge. Then the gauge gets power from a pink wire. You can test for power at the pink wire. If it has it, try grounding the other terminal and see if the gauge reacts.
Logged
-Brian-
1977 Trans Am 400 4 speed
Wallington
Oracle Forum Member
Posts: 2475
Re: Fuel sending unit wiring
«
Reply #2 on:
April 11, 2021, 02:44:24 AM »
Is the gauge pegged right off the face to the right? If there is a good grounding it will pull back onto the dial. Check the ground wire under the rear panel, clean the metal and refit, easy thing to check.
Logged
Avalanche
Forum Member
Posts: 5
Re: Fuel sending unit wiring
«
Reply #3 on:
April 11, 2021, 01:28:47 PM »
Hi all - it's stuck in the middle. I disconnect the wire near the tank and the gauge goes past full, which from I read is right - I just have to ground it now to insure it goes to empty. If that happens it seems I have an issue with the sending unit. Right?
Logged
5th T/A
Oracle Forum Member
Posts: 1511
Re: Fuel sending unit wiring
«
Reply #4 on:
April 11, 2021, 03:08:10 PM »
Avalanche,
You are correct. Second generation Firebirds have 90 ohm sending units. 90 ohms should read a full tank and 0 ohms = empty.
As Wallington mentioned, there is a ground wire from the sending unit on top of the tank that runs to rear panel area right behind the tank. Not far from where the filler tube is located. If the ground is broken, dirty or corroded it could cause a high reading on the gage.
Logged
1980 T/A with a Pontiac 461
Gone but not forgotten;
1973 T/A 455
1975 T/A 400
1978 T/A W72
1982 T/A cross fire injected
Two wheel toys;
2014 Harley Ultra Classic Limited
2013 Honda CB1100
2010 Yamaha Vmax
1982 Yamaha Seca 750
Re: Fuel sending unit wiring
«
Reply #4 on:
April 11, 2021, 03:08:10 PM »
Wallington
Oracle Forum Member
Posts: 2475
Re: Fuel sending unit wiring
«
Reply #5 on:
April 11, 2021, 05:50:55 PM »
That seems to indicate it is grounded and gauge working, how accurately is hard to say. If you don't know the history of the sender unit then it is probably overdue for dropping the tank anyway, new fuel hoses, pickup sock, maybe a buildsheet.
Logged
firebirdparts
Jedi Council
Oracle Forum Member
Posts: 19504
Re: Fuel sending unit wiring
«
Reply #6 on:
April 12, 2021, 07:12:42 AM »
You can guess where this is going: Zero ohms is empty. The gauge has to be accurate at "E" and that's how they did it. If you can't get the gauge to show E then it's the gauge. If the gauge does show E with that wire grounded, then evidently you don't have zero ohms in the tank, for whatever reasons that could be.
The gauges do go bad somehow.
Logged
I want to be like Paul Kenny when I grow up
Joe Bays
1977 Y82 4-speed (red interior)
1978 Skybird 350
1978 Redbird 305
1979 Redbird 301 4-speed
1992 Lincoln Mark VII LSC/SE (red)
1970 Datsun Pickup
1953 Chevy pickup (converted 4x4)
1988 T-bird Turbo Coupe
Jack
Oracle Forum Member
Posts: 12453
1971 Esprit TA Clone W72 1972 Formula 68 350 HO
Re: Fuel sending unit wiring
«
Reply #7 on:
May 01, 2021, 05:22:17 AM »
It's sounds to me that your float is clogged and stuck. The gauge and wiring is fine if you disconnected the ground and the gauge dropped.
Logged
Regards, Jack
Re: Fuel sending unit wiring
«
Reply #7 on:
May 01, 2021, 05:22:17 AM »
Print
Pages: [
1
]
« previous
next »
»
TAC Tech
»
Electrical
»
Fuel sending unit wiring